Menu
Back to Skills

How to: Build the perfect arrow part 1

Arrows in quiver

This is the first part of a two-part series on building the perfect arrow

The goal of any bowhunter is to have an arrow fly perfectly straight out of your bow, shot after shot. This end result is a form of art. Achieving perfect flight takes patience, quality equipment, knowledge of bow setups and a quality pro shop or the right tools to get the job done yourself. 

Building the best arrow possible is a pivotal part of a forgiving and accurate setup. You can build a better arrow by using the best materials. This includes everything from the arrow shaft itself to the glue used to attach the components. Precision equipment will ensure that your arrows are precisely made.

Tools needed
Arrow saw Arrow squaring device
Silver marker Small wire brush
Water container Soap
Cork plugs SOS pad
Grain weight scale Computer with Excel
Masking tape Q-tips
100% pure acetone Fletching jig
Digital caliper Vane glue
Epoxy Spin tester

 

It is easier to create arrows that weigh close to the same weight if you start out with a lot of arrows, rather than building a few arrows here and there in the off season. I prefer to do this with two dozen or more arrows at a time. This ensures that I do everything the same and it also aids in having enough components to properly sort in case I need a lighter insert or heavier nock to match up with the rest of the arrows.

The following detailed steps will help you create arrows that are for the most part, clones of each other, which will create tighter groups and increased confidence in your setup.

Steps to building identical arrows

Selecting and cutting arrows

First you need to select arrows for correct spine (check out this article for help). Next, determine what length arrow you will need based on charts or from entering your bow and arrow information into an archery software program.

Determining arrow spine and length

I prefer to use The Archery Program or Archers Advantage. Experiment with different arrow lengths, point weights, and fletching options in the program to create your ideal setup. When cutting arrows, be sure to use a quality high speed saw that is specifically designed for arrows. Other than for safety reasons, this will aid in providing a true cut. 

Cut a little from each side of the shaft to ensure straight ends on the arrows. Straightness flaws usually come from the front and backside of an arrow. You never really know how exact a manufacturer is when mass cutting the arrows. Before doing this, make sure that you are not cutting an arrow that is tapered or barrelled from both sides. Then cut the arrows to the correct length.

Cutting arrows

Squaring point and nock end

Square the arrow up. Start with a silver marker and mark the nock and point end of each shaft.

Silver mark for squaring arrows

Then take the shaft and carefully use an arrow squaring device to square up the ends of the arrow. Rotate the arrow on the squaring device until you have removed all the silver marker from the end of the shaft. Several manufacturers (G5, Firenock) make great arrow squaring devices.

Squaring ends of arrows

An arrow shaft must be square in order for the arrow nock and insert to sit properly against the shaft. If not, this will cause accuracy to suffer as the arrow will not spin true.

Floating arrows

Next determine which is the heavy side of the shaft. This is usually caused by a seam on the arrow where the carbon layers overlap because this area is heavier. The easiest way to determine this is by spinning the shafts in water. Floating arrows is an easy method for finding the stiffest (heaviest) side of the shaft. This is beneficial during the fletching process because you will start fletching on this stiff side of the arrow. All of your arrows will be fletched the same and it also allows you to index your nocks in the same position. Fill a bathtub or something similar with enough water to spin the shafts. 

Cork on end of arrow

Take two small corks or nocks and plug each side of the arrow to prevent any water from entering. 

Take some dish soap and pour it into the bathtub in a serpentine pattern up and down the tub. Do not agitate the water to form bubbles on the surface because this will not allow the arrow to spin freely. To avoid this, take your hand and gently place it in the water and carefully run it across the bottom of the tub to mix the soap with the water.

Floating arrows

Place the arrow in the water and spin it. Once the arrow stops spinning, take note of the side that is up and spin the arrow a few more times to ensure that it stops in the same spot. After you do this, take the arrow out of the water and place a mark on the back of the shaft on the nock side that was below the surface of the water. This is the heavy side of the arrow. Later, you will place one of your vanes on this heavy spot to keep all arrows the same.

Cleaning arrows for fletching process

Once you have finished floating the arrows, take an SOS pad and place some drops of dish soap on it and place it under hot water while rubbing the SOS pad on the fletching side of the arrow to remove oils and to roughen it up.

SOS pad to clean arrow shaft

This will allow the fletching and/or wrap to adhere better.

Next week's article will take you through sorting arrows based on weight, applying inserts and the fletching process.

(Update February 10, 2015, Part two can be found here)

12 Comments

Log in or register to post comments.

hybridauth_Facebook_1153775563
Will L. - posted 4 years ago on 02-05-2015 07:52:49 pm
Williston, ND
goHUNT INSIDER

Sweet article man. Ready for round 2 for sure!

Dustin G. - posted 4 years ago on 02-04-2015 02:33:14 pm
Chico, Ca
goHUNT INSIDER

Makes sense, I was reading it wrong. I thought you were saying the back vs the front of the arrow. That's a good idea never thought of that. Thanks for clearing it up for me!

Brady J. Miller
Brady M. - posted 4 years ago on 02-04-2015 01:00:33 pm
Las Vegas, NV
goHUNT Team

@Will, it is an attachment made specifically for Bitzenburger jigs by a company called Zenith Archery Products. The product is called the Zenith Bitzenburger Upgrade. I will provide a link to the upgrade kit and photo of it in the next article.

@Dustin, the next article will provide close up photos of what I am talking about to help clear things up. Basically it is like running a different colored vane to use for a cock vane only this time that cock vane is in the same location from arrow to arrow. Starting your fletching process on the heavy side of the arrow (still on the nock end) allows each arrow to have the vanes fletched in the same location on the shaft. So you always start with one vane on the "heavy" side mark to keep things consistent from arrow to arrow. Let me know if that helps, photos on the next article will make this much clearer. Glad you enjoyed this process. Looking forward to sharing more information.

Dustin G. - posted 4 years ago on 02-04-2015 12:51:37 pm
Chico, Ca
goHUNT INSIDER

Hey Brady, just curious, why would you put your fletching on the heaviest/stiffest side, wouldn't you want the front of the arrow to carry the weight? Unless I'm just reading it wrong. Good article and can't wait for part two.

willtcooper
Will C. - posted 4 years ago on 02-04-2015 11:52:50 am
Ponder, TX
goHUNT INSIDER

Im interested to see the custom attachment. Is it something that you came up with and had made or is it offered through Bitz ?

Brady J. Miller
Brady M. - posted 4 years ago on 02-04-2015 09:21:23 am
Las Vegas, NV
goHUNT Team

Thank you, Alexander. Glad you enjoyed it. Part two will publish next week.

Brady J. Miller
Brady M. - posted 4 years ago on 02-04-2015 09:20:42 am
Las Vegas, NV
goHUNT Team

@Will. Great choice on the Bitzenburger. In my next article you will see some photos of my Bitz jig with a custom attachment for arrow shafts. It is a little more precise than the stock one. Both get the job done great, but the attachment has some tighter tolerances.

alex.penulo
Alexander K. - posted 4 years ago on 02-04-2015 07:05:04 am
Denver, CO
goHUNT INSIDER

Great article! I look forward to part 2.

willtcooper
Will C. - posted 4 years ago on 02-03-2015 04:03:18 pm
Ponder, TX
goHUNT INSIDER

Im slowly but surely putting together all the tools needed to build my arrows from the ground up. Next is the arrow saw.

willtcooper
Will C. - posted 4 years ago on 02-03-2015 04:02:21 pm
Ponder, TX
goHUNT INSIDER

I went with a Bitzenburger. Couldn't be happier with it.

Brady J. Miller
Brady M. - posted 4 years ago on 02-03-2015 03:52:56 pm
Las Vegas, NV
goHUNT Team

Thanks, Will. What fletching jig did you go with? I can't wait to release the follow-up article to this. Floating arrows is another key step for promoting proper arrow flight. Especially when you throw a large fixed blade broadhead on the front.

willtcooper
Will C. - posted 4 years ago on 02-03-2015 03:29:24 pm
Ponder, TX
goHUNT INSIDER

I just got my first fletching jig and have been learning more and more every day. Its fun and rewarding. Didn't know about floating the arrows. Looking forward to next weeks article.